Xenon Project is no longer in operation.

This website is maintained as reference material and a reminder
of a time before tech monopolies ruined the internet
and coronavirus ruined everything else.
Call us at 888-XENONRC | Open 10AM to 5PM PST Monday-Friday Contact | Support | Blog | Customer Login UltraCote, Transparent Orange
RC Helicopters, RC Cars, RC Airplanes, RC Trucks, RC Boats & RC Toys
You are here: Home > RC Airplanes > RC Airplane Parts > Coverings > UltraCote, Transparent Orange

UltraCote, Transparent Orange

UltraCote, Transparent Orange

CLICK TO ENLARGE

UltraCote, Transparent Orange

PN-R-50045 by Hangar 9

Retail Price: $22.49
You Save $6.50 (29%)

$15.99

Out Of Stock - Check back soon or join our waitlist!

Hangar 9 UltraCote® is a high tech polyester covering that features a unique multi temperature-controlled adhesive and shrinkage system, making it versatile and easy to apply. A patented polymerizing process permanently fuses the color to the polyester film covering, eliminating the possibilities of color-layer separation and permits repositioning the covering on your model. UltraCote's unique ability to both shrink and stretch make it superior to other coverings for going around tight curves and wingtips.

 

Temp ranges are as follows:

Adhesion to wood begins at 200 to 220 degrees F.
Shrinkage onset begins at 300 degrees F.
Maximum shrinkage is at 350 degrees F.

Detailed Information

UltraCote, Transparent Orange 
UltraCote, Transparent Orange

Surface Preparation:
The covering job can only be as good as the finish of the surface it's applied over. In order for the covering to properly adhere to a surface, the surface must first be smooth and clean. Sand the model using a sanding block and progressively finer sandpaper, with the final sanding being done with 320 grit paper. Vacuum away all of the dust, as specks of dust under the covering will leave unsightly bumps. Fill gaps and dents with a high-quality filler. If using light-colored UltraCote® (such as white or yellow), use a tan-colored filler that matches the wood color to prevent the filler from showing through.

Pro Tip - Some professional builders “raise the grain” then sand a second time with 320 or 400 grit paper for the ultimate finish. After the model is sanded, use a damp cloth to wipe down the model. Some modelers prefer to use a fine-mist squirt bottle filled with water to dampen the surfaces to be covered. As the surface dries, imbedded wood fibers in the surface will “stand up.” When dry, sand the surfaces again using 320 or 400 grit paper. Raising the grain now and sanding it off will prevent the grain from raising later under the covering, creating a bumpy finish. Vacuum the model thoroughly and avoid touching the model with oily hands.Your model is now ready for covering!
UltraCote, Transparent Orange

Trim Film to Size:
Start by covering the bottom of one wing half. Using scissors or sharp hobby knife, cut a piece of UltraCote® a few inches larger than needed to cover the wing. Remove the backing (save for later) and place the covering with the adhesive (dull) side down, centered over the wing. Set the covering iron to the application temperature of 220°F.

Pro Tip - If the iron you're using does not display the actual temperature, here is a tip that will ensure your iron is properly set.Water boils at 212°F. Allow your iron to warm up at a medium setting. When the iron reaches its stabilized temperature, carefully pour a few drops of water on the iron's surface. Adjust the temperature until the water just begins to boil off. This method is surprisingly accurate and is generally within 10° (of the exact application temperature of 220).
UltraCote, Transparent Orange Tacking Covering to Spar:
Tack the covering to the spar or the high point of the wing, using your iron as shown (an iron sock is highly recommened). Gently pull the covering toward the root and toward the tip, as you work the iron from the center of the spar to the root and tip of the wing. Press gently with the iron, allowing the heat (not pressure) to activate the adhesive and bond the covering to the high point. Ideally, the covering will naturally lay flat against the entire surface with a minimum of wrinkles.
UltraCote, Transparent Orange Covering a Solid-Sheeted Wing:
If covering a solid-sheeted wing, work from the center of the spar outward to the trailing edge and then to the leading edge as shown, using the iron at 220°F. If a wrinkle develops, the covering can be carefully lifted and reapplied.
UltraCote, Transparent Orange Covering an Open-Structure Wing:
If covering an open-structure wing, work from the spar toward the trailing edge, gently sliding the iron (set at 220°) toward the trailing edge with the iron contacting two ribs. Using your iron, adhere the covering to the remaining ribs, working toward the tip and the root. Now complete the open structure leading edge, using the same method. If the leading edge is sheeted, then follow the technique listed above under “Covering a Solid-Sheeted Wing.”
UltraCote, Transparent Orange Sealing the Edges:
With the iron set to 220°F, seal the leading and trailing edges. Using a straight edge and a sharp #11 hobby knife, carefully trim the excess covering from the leading and trailing edge, allowing a minimum of a 1/4" overlap to wrap around the leading and trailing edge of the wing. Now seal the leading and trailing edges securely with the covering iron.
UltraCote, Transparent Orange Wing Tip:
Depending on the amount of the curvature of the wing tip, high heat (up to 350°F) may be needed to shrink and stretch the covering to eliminate all the wrinkles. Preset the iron to 300°F. Pull and stretch the covering around the wing tip while applying heat with the iron. Remember, UltraCote® can be carefully lifted and repositioned to help eliminate wrinkles. This feature is beneficial, especially when covering sharply curved wing tips. Continue working, pulling, and heating the covering around the tip until the covering is past the center of the tip. It may be necessary to increase the temperature of the iron to achieve greater shrinkage to eliminate all wrinkles. Trim the excess covering using a #11 hobby knife, then reseal the covering on the wing tip
.
Pro Tip - If sealing the covering in tight areas such as corners or fillets, using the Hanger 9 ProTrim Sealing To

Features

  • High tech polyester covering
  • Unique multi temperature-controlled adhesive shrinkage system
  • Versatile and easy to apply
  • Patented polymerizing process permanently fuses the color to the polyester film covering, eliminating the possibilities of color-layer separation and permits repositioning of the covering on your model.
  • Light weight at .18 oz/sq. ft.
  • Fuel proof to glow fuel, gas, and smoke oil. Water proof as well.

In Depth

  • Length: 6.5' (78")
  • Width: 23.5"
  • Weight: .18 oz per square foot

Review Summary

This product is covered by our limited warranty policy. We stand behind our products and all items are guaranteed to be in working order and fully functional. Any items found to be defective upon arrival will be repaired or replaced free of charge within 60 days of purchase.

Returns or exchanges of new and unused products will also be accepted up to 60 days after the date of purchase.

XenonProject.com 11312 Orchard St. Unit A. El Monte, CA 91731 USA  |  888-XENONRC (888-936-6672) M-F 10AM to 5PM PST© 2012 XenonProject.com
For full size Performance Car Parts, check out our affiliate Silicone Intake Systems.
UltraCote, Transparent Orange UltraCote, Transparent Orange